High pressure plunger pump for jet grouting
A high pressure plunger pump for jet grouting must match the fluid circuit, nozzle arrangement and required pressure–flow operating point. Maximum pressure alone does not establish whether a pump can supply the intended jetting process.
Gaodetec’s GGP250/450-250D High pressure plunger pump for jet grouting is a diesel-driven, horizontal triplex plunger pump. Its published technical table lists 250 L/min at 450 bar, with an explicit note that the data were tested using water. That reference needs to be assessed against the actual project fluid and delivery system before equipment selection is finalised.
Identify whether the pump handles grout or water
The jet grouting method determines the pump’s role. Single-fluid systems use a grout jet, while double-fluid systems surround the grout jet with air. Conventional triple-fluid systems use an air-shrouded water jet and introduce grout through a separate port.
A cement slurry jetting pump therefore has a different material duty from a high pressure water pump for jet grouting. The required fluid circuit should be identified before comparing pump specifications.
For grout service, provide the cement type, mixture proportions, additives and relevant fluid properties. Water-test performance does not establish compatibility with every slurry formulation. The pump’s material limits and the approved preparation procedure must both be respected.
Interpret the published pressure–flow point correctly
The GGP250/450-250D High pressure jet grouting pump product page gives a paired output of 250 L/min at 450 bar. This is more informative than separate maximum flow and pressure figures because it identifies a stated operating combination.
However, the accompanying water-test condition remains part of that specification. The published point should not be rewritten as verified continuous delivery of cement slurry at the same pressure and flow.
For a proposed diesel driven jet grouting pump, request confirmation of the operating range for the intended medium, including the required speed or transmission setting and permitted sustained duty. Where a test is required, its fluid, duration and measurement conditions should be agreed beforehand.
The model designation alone should not replace this review. Selection needs to establish that the proposed configuration supports the required working point under the conditions relevant to the project.
Match pump outlet conditions to the jetting assembly
The pressure measured at the pump outlet is not automatically the pressure available immediately upstream of the nozzle. Losses occur through the delivery hose, fittings, rotary connection and drill-string passages. Elevation differences also affect the pressure balance.
Provide the full delivery arrangement when requesting a high pressure grout pump. Hose length and internal diameter, treatment depth, drilling equipment restrictions, and nozzle number and diameter all influence the assessment.
The nozzle arrangement links discharge flow with pressure. Changing the nozzle size or number changes the required duty, so the pump and jetting assembly should be reviewed together.
Column geometry and treatment results also depend on ground conditions and the approved jetting procedure. A pump pressure rating does not independently establish column diameter, strength or permeability.
Supply the triplex plunger pump with suitable slurry
The GGP250/450-250D uses three plungers in a single-acting reciprocating arrangement. Reliable operation requires the pumping chambers to receive suitable material under the manufacturer’s specified inlet conditions.
The mixing plant must therefore be assessed alongside the triplex plunger pump. Its practical preparation rate, holding arrangement and transfer capacity need to support the planned jetting operation.
A large agitator can provide a reserve, but it cannot compensate indefinitely for a preparation rate below withdrawal demand. Likewise, increasing the pump speed does not resolve restricted inlet supply.
Confirm the required material screening, inlet connection and supply arrangement for the proposed pump. Access for inspection, cleaning and replacement of wear components should be considered when positioning the equipment.
Confirm the complete equipment configuration
The product page includes an upgraded GGP250/450-250D configuration. Buyers should obtain a configuration-specific technical sheet rather than combining details from different versions.
For jet grouting equipment procurement, confirm the engine, transmission, inlet and outlet connections, dimensions and supply scope in one agreed document. The high-pressure hose assembly, fittings and protective devices also need to suit their specified duties.
A useful acceptance test reports pressure and flow together. A pressure reading without corresponding flow does not demonstrate the required pumping duty, while a free-discharge flow test does not establish performance against the intended resistance.
For a Gaodetec quotation, provide the jet grouting method and fluid circuit, required pressure–flow point, grout specification, hose and drill-string arrangement, and site operating conditions.
Contact info@gaodetec.com to discuss the GGP250/450-250D high pressure plunger pump for jet grouting and request a configuration-specific quotation.